打膠機打膠不飽滿該怎么辦？
打膠機打膠不飽滿，怎么解決？實際上，打膠機存在這個問題，主要是由以下兩種情況引起的！
Glue machine is not full, how to solve? In fact, this problem is mainly caused by the following two situations!
1.打膠速度過快
1. Glue speed is too fast
一些客戶為了加快生產節奏以跟上生產計劃，將打膠機速度調的過快，導致膠水不能完全滿足合格標準的機頭就已移下一個位置進行打膠水操作。
In order to speed up the production pace and keep up with the production plan, some customers adjust the speed of the gluing machine too fast. As a result, if the glue can not fully meet the qualified standard, the machine head has been moved to the next position for gluing operation.
打膠機
Glue machine
如果需要加快打膠速度來調整打膠機的運動參數，那么還應該設置相應的涂膠系統。例如，這時候我們就需要加大供膠壓力，增大打膠機的出膠速度來配合對象的移動速度的增加。
If it is necessary to speed up the gluing speed to adjust the motion parameters of the gluing machine, then the corresponding gluing system should also be set. For example, at this time, we need to increase the glue supply pressure, increase the glue speed of the beater to match the increase of the moving speed of the object.
如果我們僅增加打膠機的速度而不調節壓力，則很有可能膠水涂的不飽滿。
If we only increase the speed of the glue machine without adjusting the pressure, it is likely that the glue will not be fully applied.
2.供膠壓力不足
2. Insufficient glue supply pressure
實際上在前一種情況中已經描述了這種情況。即使不調整打膠機的移動速度，膠水也未滿的情況，這可能是由于供膠壓力太小所致。此時，我們只需要調整打膠機的供膠壓力即可解決此問題。
In fact, this situation has been described in the former case. Even if the moving speed of the glue machine is not adjusted, the glue is not full, which may be caused by too small glue supply pressure. At this time, we only need to adjust the glue pressure of the glue machine to solve this problem perfectly.
打膠機
Glue machine
3.機頭感應器損壞
3. The head sensor is damaged
這種情況很少見，但并不排除這種情況。在打膠機中，有一個用于檢測鋁條深度的傳感器。如果鋁條太深或太淺，它將自動調整移動速度和供膠壓力（自動調整是小范圍的）。如果我們的鋁條深度不同，在加上感應器損壞，打膠機就會出現打膠不飽滿的情況！
This is rare, but it is not ruled out. In the gluing machine, there is a sensor for detecting the depth of the aluminum strip. If the aluminum strip is too deep or too shallow, it will automatically adjust the moving speed and glue supply pressure (automatic adjustment is small range). If the depth of our aluminum strip is different, and the sensor is damaged, the gluing machine will not be full!
上一篇：中空玻璃打膠機耗電量高不高？
下一篇：中空玻璃加工設備的提高技術
