如果打膠機沒有自動清洗功能要如何清洗？
如果是自動清洗的打膠機，操作相當簡單。只需按操作面板上的清洗按鈕，機器就會自動完成清洗。那么如果機器沒有自動清洗功能，該如何清洗呢?
濟南雙組份打膠機廠家給您建議。
If it is an automatic cleaning glue applicator, the operation is quite simple. Just press the cleaning button on the operation panel, and the machine will automatically complete cleaning. How to clean the machine if it does not have automatic cleaning function? Jinan two-component sealant manufacturer gives you suggestions.
先來，看看膠水的性質。如果膠水是單液，在室溫下不易凝固，那么下次使用的膠水在每一點或產品填充后都是一樣的，就不能考慮清洗問題了。如為厭氧膠、快干膠、401502膠或硅膠膠等常溫下會快速凝固的膠，應清洗干凈。清洗時，先將未使用的膠水瀝干，再將天南水、工業酒精等有機溶劑放入機器內。然后把這些有機溶劑壓在一起，用氣槍把它們吹開。
First, look at the properties of glue. If the glue is a single liquid, which is not easy to solidify at room temperature, the glue used next time will be the same at every point or after the product is filled, so the cleaning problem cannot be considered. If it is anaerobic glue, quick drying glue, 401502 glue or silica gel glue that will rapidly solidify at room temperature, it should be cleaned. When cleaning, drain the unused glue, and then put organic solvents such as Tiannan water and industrial alcohol into the machine. Then press these organic solvents together and blow them away with an air gun.
對于這種機器，清洗是非常必要的。否則膠水在膠閥或料筒內固化會很麻煩，有些配件可能需要更換。所以每次用的時候，一定要記得清洗!雙組份打膠機的a、B膠的混合部分在出膠口只有混合管，所以清洗部分只有混合管，其他部分不需要清洗;
For this kind of machine, cleaning is very necessary. Otherwise, it will be troublesome for the glue to solidify in the glue valve or cylinder, and some accessories may need to be replaced. So every time you use it, remember to clean it! The mixing part of glue a and glue B of the two-component sealant beater only has a mixing pipe at the glue outlet, so the cleaning part only has a mixing pipe, and other parts do not need to be cleaned;
如果是雙組份打膠機，清洗比較簡單。工作完成后，將打膠機前的白色攪拌管拆下，浸泡在有機溶劑中，或更換攪拌管。
If it is a two-component sealant dispenser, cleaning is relatively simple. After the work is completed, remove the white mixing pipe in front of the glue applicator, soak it in organic solvent, or replace the mixing pipe.
總之如果打膠機沒有一鍵清洗功能，清洗時先將未使用完的膠水排干，然后將有機溶劑，如天那水、工業酒精等放入機器內；然后將這些有機溶劑和膠水一起壓出來，再用氣槍吹開即可。用此類型的機器，清洗是十分必要的，否則的話，長時間不用，膠水固化在膠閥中，或者是料桶中就很麻煩，可能有些配件就要更換了。
In a word, if the glue dispenser does not have one key cleaning function, drain the unused glue before cleaning, and then put organic solvents, such as Tianna water and industrial alcohol, into the machine; Then press these organic solvents and glue together, and blow them with an air gun. With this type of machine, cleaning is very necessary. Otherwise, if it is not used for a long time, it will be troublesome if the glue is solidified in the glue valve or in the bucket. Some parts may need to be replaced.
So every time you use it, you must remember to clean it. For more information about the glue dispenser, please come to our website http://www.g89.com.cn Consult and understand!
上一篇：雙組份打膠機的故障重要出自這幾方面
下一篇：雙組份打膠機出現斷膠的解決方法
