雙組份打膠機的保養注意哪些？
1、壓盤上的放氣閥門要保持通暢，要定期疏通和清洗。
1, the vent valve on the pressure plate should be kept open and regularly dredged and cleaned.
2、正常工作時不要斷氣源，如果發現斷氣源應停止工作。
2, do not interrupt the source of gas when working normally. If you find the source of gas, you should stop working.
3、若涂膠工作過程中停頓時間超過15分鐘以上時，一定要用“沖槍”。本機有報警功能，到時沒有沖膠會有蜂鳴器報警。
3. If the pause time is more than 15 minutes in the process of gluing, you must use the "punch gun". This machine has alarm function. When there is no glue, there will be a buzzer alarm.
4、定期檢查氣源，應保證使用經干燥的潔凈壓縮空氣，并定期排放分離過濾器中的積水，檢查油霧器中的油是否夠用。
4. Regular inspection of the gas source, first of all, should ensure the use of dry clean compressed air, and regular discharge of separation filter water, check whether the oil mist is enough.
5、硅酮膠B 組份遇空氣會結殼，影響泵的正常工作和管路的暢通，因此，停機時B組份膠的所有通道在泄壓后均應關閉，使B組份不得接觸空氣。
5. Component B of silicone glue will crust when it meets the air, which will affect the normal operation of the pump and the smooth flow of the pipeline. Therefore, all channels of component B glue should be closed after pressure relief, so that component B can not touch the air.
6、B膠桶內如果要有空氣，空氣將排不出來，B泵將快速往返運動，不能向高壓泵內正常供膠，影響整個系統，因此，必須將空氣排出來。方法是：將壓盤提出從新壓入并放氣。
6. If there is air in the B glue bucket, the air will not be exhausted, and the B pump will move back and forth quickly. It can not supply glue to the high-pressure pump normally, affecting the whole system. Therefore, the air must be discharged. The method is to press the pressure plate forward and deflate.
7、液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍，否則B組份管路壓力將升得很高，造成事故。
7. The pressure of the hydraulic station system can not be adjusted too high, according to the indoor environment temperature and other actual conditions, adjust to meet the normal rubber nozzle glue evenly. Must open the glue gun when opening the hydraulic station, otherwise the pressure of B component pipeline will rise very high, causing safety accidents.
8、A膠提膠泵連續工作1分鐘以上沒有供膠停止，說明管路內有空氣，此時會報警，須打開泵上管接頭再打開A膠提膠泵，直到出膠為止，停止并接好接頭，膠槍會出現有空氣的嗶嗶爆破聲，空氣排凈就好了。
8. A glue pump continuous work for more than 1 minute without glue supply stop, indicating that there is air in the pipeline, at this time will alarm, must open the upper pipe connection of the pump and then open the A glue pump, until the glue out, stop and connect the joint, the glue gun will appear air beep explosion sound, air drain is good.
9、由于每次沖洗混合器不會完全干凈，每次都有少量的混合膠沉積，越來越多，以致堵塞混合器通道，用一段時間后，影響出膠量和混合效果，因此要定期（聚硫膠五天，硅酮膠兩天）清洗混合器。把混合器內的混膠棒拆出，如有損壞更換新的混膠棒。若混膠棒拆不出來，可用火燒掉，注意不能損傷零件螺紋。
9. Because the mixer will not be completely clean every time, each time there is a small amount of mixed glue deposition, more and more, resulting in blocking the mixer channel, after a period of time, affecting the amount of glue and mixing effect, so regularly (polysulfide five days, silicone two days) to clean the mixer. Disassemble the mixing stick in the mixer and replace the new mixing stick if there is any damage. If the mixing stick can not be removed, it can be burnt down. Attention must not be given to screw threads.
This article is supported by a two-component dispenser. For more details, please click on our official website http://www.g89.com.cn. We will provide you with satisfactory service wholeheartedly.
上一篇：雙組份打膠機的特點
下一篇：高粘度齒輪計量泵在雙組份打膠機起到什么作用?
